To ensure uninterrupted pressure of water, it is
advisable to keep the pipelines
with minimum number of bends, which will support smooth flow of water.
All the supply lines must have vent pipes. these
vent pipes help in removing
air-locking in the water supply to give a smooth flow of from the fittings.
Prior to plastering or fixing tiles, test the
working of all the installed concealed
fittings on a high pressure to check for leakage insert, if any.
Use 25mm pipelines rather than 20mm which will
help in overcoming scaling inside the
pipelines and will sufficient space for the water flow.
Place the outlet point in the overhead tank least
25cm above the ground level of the
tank. this prevents the flow of foreign particles, sand etc., along with water
supply in to the fittings and thereby prevents the possible damage to the working
parts. clean the tank thoroughly before the supply starts. it is suggested that the
overhead tank must be cleaned at regular intervals to avoid in flow of foreign
particles.
Clean the aerators provided in the items at
regular intervals for a perfect foam
flow of water from the fittings.
To product the fine finish of fittings from dirt,
stains and other damages during
construction, cover them with cloth or polypack after their installation, till they
come into actual use.
Clean the fittings regularly with normal soap or
remove scaling or stains. do not
use strong detergentsas this may cause damage to the chromium finish used on all
company products.
It is suggested that center to center distance
for hot & cold inlet for all wall
mounted mixtures should be maintained at 165mm where any of our wall mixers from
different ranges can be easily installed without any problem.
Do not use harsh cleaning agents containing
abrasives and acids. instead, use a soft
sponge or wet cloth with soapy water or diluted vinegar to protect the colour coated
finish.
Buy company products from company’s authorised
dealers only to ensure genuine
quality materials.
Oricon
Product Care
The Best General Maintenance Is Regular
Cleaning – Wipe The Tap With A Dry
Towel After Use Even though our finshes are considered durable, you
should never use any abrasive type cleaners, clothes, or pads to clean your
fixtures. Always try and keep your finshes clean and dry. Trapped moisture on the
surface of your finish can lead to staining and scaling. Astringent cleaners,
chlorine, bleach, along with acidic based organic cleansers are potentially harmful
to these finishes. Chrome plated finishes are very tarnish resistant. However, they
are not indestructible and can scratch and mar.
Do not allow water spots to dry on the fixture.
Keep the surface clean and dry after
use.
Periodic cleaning can be done by applying mild
soap with a soft clean cloth to
gently remove surface spots.
Never use cleaners with bleach, abrasives, or
vinegar. Never use any type of
abrasive pad or sponge.
What Cleaning Products Can Cause Damage
To Finishes? Always blot
dry any water from faucet surface. Allowing water to evaporate on the surface can
lead to build up of mineral deposits. Cleaning with a damp non-abrasive sponge and
buffing it dry with a clean soft cloth should help keep your product looking
beautiful. To remove water spots, use warm water and a soft, damp cloth. Hard water
stains may be removed using a 50/50 solution of white vinegar and water. Make
certain that you rinse thoroughly with water afterward.
Avoid using the following which can damage your
finish.
Avoid industrial cleaners and abrasive cleaners,
such as those used for toilet
bowls, green Scotch Brite heavy duty scrub sponges, Scrubbing Bubbles Bathroom
Cleaner and Lysol Basin Tub, Soft Scrub, and Tile Cleaner.
Avoid products that state on the label that they
remove tarnish and rust, and those
containing hydrofluoric, hydrochloric and/or phosphoric acids and caustic agents.
Avoid harsh abrasives or polishes.
Avoid bleach-based cleaners.
Please Note: We are committed
to providing you with the best
quality and cosmetic finish to your sparkling new faucet each time, every time.
Please ensure the installer, technician or plumbers handle and install the product
with due diligence, it is very easy for someone to blame a third party if the
product is damaged.
Oricon
Warranty
CONDITIONS OF WARRANTY In
case of only manufacturing defect in
the product, company shall either repair the defect or replace the piece with a
product of equivalent value.
This warranty will not be valid for the products
for or parts there of that don’t
use originalcompany spare parts and which have been repaired by unauthorized /
unqualified persons.
In case of any amendment made to the certificate,
this warranty is non-transferable
and invalid.
The customer will have to bear the risk and cost
of returning the product that is
found to be defective during the specified period to company.
Company shall not be liable for any incidental,
consequential, exemplary, special or
punitive damages, or for any loss of revenue, profit or use arising out of breach or
this warranty or in connection with the sale, maintenance, use, operation or repair
of any company product. in no event will company be liable for any amount greater
than the purchase price of a defective product.
This warranty specifically excludes hoses, rubber
components and other consumable.
Customer are require to keep original invoice and
warranty card safely and need to
produce the same when asked in order to avail this warranty.
Damage of any product or parts there of due to
any of the following causes will not
be covered under this warranty.
User’s or its agent’s misuse, negligence, accident or faulty installation.
Improper maintenance of the product by not abiding the company printed
instruction manual / customer guidelines.
Dirt, lime-scale or aggressive cleaning chemicals.